Carrera GT Heroes Instructions d'exploitation télécharger pdf (Page 6)

1 LED on = low braking eﬀ ect

5 LEDs on = high braking eﬀ ec

Setting fuel tank capacity

Pit Stop 30346

2 3

1 – 10

(individually for one and/or several cars)

Activate fuelling function at the Black Box.

Plug any speed controller in connector 3. Switch oﬀ Black Box,

place car/s on the track, push lane-change-button and keep it

pushed while Black Box is switched on again. Don´t release the

lane-change-button until the 1st LED lights red. Fuel capacity is

set by pushing lane-change-button. Conﬁ rm by pressing speed

controller´s tappet (=> middle LED will light).

Before the start return speed controller to the original connector!

1 LED on = low fuel capacity

5 LEDs on = full tank

Refuelling:

Depending on the fuel capacity the car´s lights start to ﬂ ash after

some time, the car slows down and might start to stutter. For refuel-

ling enter the Pit Stop and release the speed controller´s tappet.

(Fuelling amount depends on car´s standing time in the Pit Stop).

a) Filling up: wait until car´s lights stop ﬂ ashing.

b) Partial refuelling: start while car´s lights still ﬂ ash.

c) Non-refuelling: car drives on at reduced speed.

Car programming

from DIGITAL 132

to Evolution (analogue)

Place car on the Evolution track and push speed controller´s tappet

three times (thumb). Push the switch for changing the running direc-

tion acc. ﬁ g.

. For Carrera DIGITAL 132 operation mode return

the switch to original position.

Replacement of double sliding

contact and guide keel

2 a 2 b

Advice:

• It is recommended to always take out and change only one

grinder.

• Never pull the vehicle backwards, because the grinders could be

damaged otherwise.

Please carefully pull out the guide keel according to ﬁ g.

When changing the double contact brushes please take care

that in stage one the upper contact brush

is only pulled out

partly and that in stage two the double contact brush can be pulled

out completely with the contact brush

. For inserting please

proceed the same way.

Changing the rear axle

2 3

Take oﬀ the vehicle´s upper part from the chassis as per ﬁ g.

Remove the axles from the bearings positions with pressure (

Insert new axle. Pay attention to the correct position of the axle

bearings (

Maintenance and care

To ensure a proper operation of the motor-racing circuit, all race-

track components should be regularly cleaned. Pull the plug prior to

cleaning.

Racetrack: Keep the track surface and track slots clean with a

dry cloth. Do not use any solvents or chemicals for cleaning. When

it is not in use, store the racetrack in a clean and dust-protected

location, preferably in the original cardboard box.

Car check: Clean axle and wheel bearings, pinion gears, gear-

wheels and bearings and lubricate using a resin- and acid-free

grease. You can use a toothpick or similar as aid. Regularly check

the condition of sliding contacts and tyres.

Troubleshooting

Driving tips

Troubleshooting:

In case of any malfunctions, please check the following:

• Has the connection to the power supply been established cor-

rectly?

• Have transformer and speed controllers been connected

correctly?

• Are the track connections faultless?

• Are the racetrack and track slots clean and free of any foreign

objects?

• Are the sliding contacts in order and do they make contact with

the track slot?

• Are the cars correctly coded to the according speed controller?

• The track‘s current feed will be switched oﬀ automatically for 5

seconds, if there is an electrical short circuit: this will be notiﬁ ed by

audible and visual signals.

• Are the cars placed on the track in running direction? In case of

non-functioning push the running direction switch which is on the

car´s bottom.

Note:

During operation small car parts as spoilers or mirrors may get oﬀ or

brake due to being original detailed parts of the car model. To avoid

this it is possible to remove them before operation.

Driving technique:

• You can drive fast along the straight track but you should brake

before the curve and then accelerate again when coming out of the

curve.

• Do not fasten or block the vehicles when the motor is running:

overheating or damage to the motor could result otherwise.

Note: When using track systems which are not manufactured by

Carrera the existing guide keel has to be replaced by the special

guide keel (#85309). While using the Carrera crossing (#20587) or

high banked curve 1/30° (#20574) slight driving noise might occur

which is due to the full-scale genuineness and does not aﬀ ect ﬂ aw-

less operation.

All Carrera spare parts are available in the webshop:

www.carrera-toys.com

Delivery exclusively to Germany, Austria, Netherlands, Belgium and

Luxembourg.

Technical specifications

Output voltage: Toy transformer

14,8 V

51,8 VA

This device is marked by “selective sort throught” symbol related to

sort through domestic, electric and electronic, waste.

This means the product must be treated by a specialized “sorting/

collecting” system in accordance with European directive 2002/96/

CE, to reduce the impact upon environment.

For more precise information, please contact your local administra-

tion.

Electronical product which are not going through special collect-

ing, are potentially dangerous for environment and human health,

because of dangerous substance.

Output voltage: Toy transformer

14,8 V 42,9 VA

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Carrera GT Heroes Instructions d'exploitation Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Véhicules-jouets Carrera GT Heroes